Indigo Ciara: toilet roll holder, bottle trap, hand shower and ceiling shower arm
Indigo Ciara is a range of round based bathroom fittings in chrome and matte black. Four pieces are in this collection: a wall mounted toilet roll holder, a 40mm bottle trap, a hand shower on an adjustable bracket and a 300mm ceiling shower arm. They are made to sit with other Indigo products, so a bathroom can be finished from the wall to the waste in one finish.
People search for it as Indigo Ciara and Indigo range. This page sets out what each piece does, the sizes that decide fit and how to fit and look after the fittings. For the wider choice, see Indigo bathroom accessories, Indigo showers, shower arms and bottle traps.
The Ciara pieces
| Piece | Key facts | Finish in this collection |
|---|---|---|
| Toilet roll holder | Wall mounted; 83mm projection, 150mm long, 50mm round plate; metal, chrome plated | Chrome |
| 40mm bottle trap | Metal, electroplated; connection 431mm from the wall | Matte black |
| Hand shower with adjustable bracket | WELS 3 star, 9 litres a minute; pressure 150kPa to 500kPa; bracket pivots up and down | Chrome and matte black |
| Ceiling shower arm, 300mm | 300mm high, 50mm round base; pressure 150kPa to 500kPa | Chrome and matte black |
Toilet roll holder
The holder is a single arm on a round plate, fixed to the wall beside the toilet. The plate is 50mm across, the arm is 150mm long and the holder stands 83mm from the wall. It is metal with a chrome plated finish. A roll sits on the arm and can be changed without taking the holder off the wall. Fix it at a height and distance that can be reached by a seated person, about 600mm to 700mm above the floor and 150mm to 200mm in front of the front edge of the pan.
| Measure | Figure | Why it matters |
|---|---|---|
| Plate diameter | 50mm | The fixing needs a flat area of tile or wall |
| Arm length | 150mm | Holds a standard roll |
| Projection | 83mm | The holder stands this far from the wall |
| Height from the floor | About 600mm to 700mm | Within reach of a seated person |
Fixing rails and hooks
The fixing distance is the number to measure on the wall, not the overall length. Mark it, level it, then drill, and check the backing behind the wall before you fix. A double rail projects further than a single rail, so leave clear wall beside it. A rail that carries wet towels should be fixed to a stud or to blocking, or with heavy duty anchors in a hollow wall, because plasterboard alone will not hold the load.
40mm bottle trap
A bottle trap is the trap under a basin, shaped like a bottle, that holds a seal of water to block drain smells. It sits where it can be seen, under a wall hung basin or a pedestal, so the finish matters. The Ciara bottle trap is matte black, made of electroplated metal, and it suits 40mm pipework. It replaces a plastic trap with a metal one that matches the taps. The connection is 431mm from the wall, so check that the basin and the cabinet leave room for the trap to hang.
The 40mm seal is not in the box, so the plumber supplies one to suit the pipework. Check the trap against the position of the waste outlet and the wall pipe before you order, and allow for the plumber to adjust the pipe.
Hand shower with adjustable bracket
The hand shower comes with an adjustable wall bracket and a hose. The bracket pivots up and down, so the head can be set at a height for a standing adult and lowered for a child or a seated user, which means it can be used as a main shower and not only as a hand shower. It fits onto an existing shower spigot, which makes it a good retrofit: the plumber connects the hose to the existing outlet and fixes the bracket to the wall. It is rated WELS 3 star at 9 litres a minute and works on a supply of 150kPa to 500kPa.
| Feature | Detail | What it means |
|---|---|---|
| Bracket | Adjustable, pivots up and down | Head height can be set for each user |
| Water use | WELS 3 star, 9 L/min | A middle rating with a fuller spray |
| Operating pressure | 150kPa to 500kPa | Suits most mains supplies; low pressure supplies may feel weak |
| In the box | Hand shower, wall bracket, hose, instructions | Everything needed for a retrofit |
Ceiling shower arm, 300mm
The ceiling arm is a 300mm long, round based arm that drops from the ceiling to hold a shower head. It stands 300mm high, with a round 50mm base that sits on the ceiling. The length sets the height of the head. On a ceiling of 2400mm, a 300mm arm puts the head about 2100mm above the floor, which is a good height for most adults. On a ceiling of 2700mm, the head sits at 2400mm, which is higher. Check the ceiling height before you order. The arm works on a supply of 150kPa to 500kPa.
| Ceiling height | Head height with a 300mm arm | Comment |
|---|---|---|
| 2400mm | About 2100mm | A good height for most adults |
| 2550mm | About 2250mm | Suits a tall user |
| 2700mm | About 2400mm | Higher than usual; consider a shorter arm elsewhere |
Setting shower heights
Shower heights are fixed at rough-in, before the tiles go on, so decide them early. A fixed wall head sits 2000mm to 2100mm above the finished floor, measured to the centre of the arm outlet, and a household taller than 190cm should go to 2100mm to 2200mm. The top of a rail is usually 1800mm to 1900mm, and the holder slides down to a comfortable height. A wall mixer sits 1000mm to 1100mm from the floor, centred in the shower space. Leave a margin of 15cm to 20cm above the head of the tallest user, and tell the plumber the heights before the linings are fixed.
Pressure, flow and head size
The supply decides how big a head can be. Round fixed heads usually run from 200mm to 300mm. On a low pressure supply, a smaller head of 150mm to 200mm gives a better spray, and a head larger than 250mm can feel weak unless a pump is fitted. A typical shower flow is 5 to 9 litres a minute, and a flow restrictor in the head keeps the use down. A simple test is to time how long a 10 litre bucket takes to fill. If it fills in under 60 seconds the pressure is good for a large rain head. A tank or gravity supply is usually best with a 3 star head.
Chrome or matte black
| Finish | Look | Suits |
|---|---|---|
| Chrome | Bright and reflective | Most bathrooms and a match for chrome taps |
| Matte black | Flat and dark | White tile, timber vanities and pale walls |
The shower pieces come in both finishes, the toilet roll holder is chrome here and the bottle trap is matte black. Choose one finish for a bathroom and match the tap, the arm, the hand shower and the accessories. If the bottle trap is matte black, a matte black tap and basin waste give a calm line under the basin.
The order of the work
| Stage | Piece | Why then |
|---|---|---|
| Before the ceiling is lined | Ceiling shower arm | The pipe and the fixing go behind the lining |
| Before the tiles | Hand shower bracket position | The outlet must meet the finished tile |
| After the basin is fixed | Bottle trap | The trap hangs from the waste |
| After the tiles and the paint | Toilet roll holder | The wall is finished and the backing is known |
Fitting
A licensed plumber should connect the shower and the trap, because they join the water supply and the drain. Fit the arm and the hose by hand and snug the washers flat, then run the water to check each joint. For the toilet roll holder, mark the height with a level, drill the tile with a tile bit and fix the plate with the kit. Check that each fitting sits square before the final tightening.
Caring for the finish and the nozzles
Wipe the metal with mild soapy water and a soft cloth after cleaning, and dry it so water does not set on the surface. Put the cleaner on the cloth and not directly on the fitting. A mild citric acid cleaner is safe for descaling a head, but avoid acetic acid, hydrochloric acid and chlorine bleach, and never mix cleaners. Keep abrasive tools and steam cleaners away from coated finishes. Check the aerator and the nozzles from time to time, because scale builds up fastest in hard water.
Caring for chrome and matte black
Wipe both finishes with a soft cloth and warm water, and a little mild soap if needed. Dry them so water does not set on the surface. Keep bleach, harsh cleaners and abrasive pads away, since they dull a plated finish. Matte black marks if it is scrubbed, so use a soft cloth only. Clean the hand shower nozzles with a soft brush now and then to keep the spray even.
Before you order
List the pieces you need, choose one finish and check the ceiling height, the supply pressure, the waste position and the wall space. Set out the heights for the arm and the holder on a plan, and book a licensed plumber for the shower and the trap.
