Skip to content

Freestanding and Swivel Rails

5 Items

  • $131 Off RRP
    Thermogroup 8 Bar Straight Flat Freestanding Heated Towel Rail 590mm

    Thermogroup 8 Bar Straight Flat Freestanding Heated Towel Rail 590mm

    Checking delivery...
    $464
    $131 (-22%) OFF RRP of $595
    $131 (-22%) off RRP of $595
  • $99 Off RRP
    Thermogroup Thermorail 8 Bar Round Swivel Heated Towel Ladder 570w x 1260h - Polished SS

    Thermogroup Thermorail 8 Bar Round Swivel Heated Towel Ladder 570w x 1260h - ...

    Checking delivery...
    $896
    $99 (-9%) OFF RRP of $995
    $99 (-10%) off RRP of $995
  • $59 Off RRP
    Thermogroup Thermorail Free Standing Straight/Round 600x1080x300mm 110Watts 8 Bars - Matt Black

    Thermogroup Thermorail Free Standing Straight/Round 600x1080x300mm 110Watts 8...

    Checking delivery...
    $530
    $59 (-10%) OFF RRP of $589
    $59 (-10%) off RRP of $589
  • $116 Off RRP
    Thermogroup Thermorail Swivel Straight/Round 595x540x104mm 40Watts 4Bars - Polished Stainless Steel

    Thermogroup Thermorail Swivel Straight/Round 595x540x104mm 40Watts 4Bars - Po...

    Checking delivery...
    $464
    $116 (-20%) OFF RRP of $580
    $116 (-20%) off RRP of $580
  • $122 Off RRP
    Thermogroup Thermorail Swivel Straight/Round 595x540x104mm 45Watts 4Bars - Matt Black

    Thermogroup Thermorail Swivel Straight/Round 595x540x104mm 45Watts 4Bars - Ma...

    Checking delivery...
    $488
    $122 (-20%) OFF RRP of $610
    $122 (-20%) off RRP of $610

Swivel and freestanding heated towel rails buying guide

A swivel heated towel rail fixes to the wall and its bars swing out so the towels spread apart. A freestanding rail stands on the floor and plugs into a power point, with no fixing to the wall at all. For most bathrooms the right call is a swivel rail, because it takes no floor space and spreading the bars helps the towels dry. Choose a freestanding rail when the wall cannot take fixings or when you want to move the rail between rooms. This guide sets out the five Thermorail rails here, how each one is wired and fitted, and what each one uses to run.

The five rails

Rail Type Finish Bars Size (width, height, depth) Power
SV41 Swivel Polished stainless steel 4 595mm, 540mm, 104mm 40 watts
SV41B Swivel Matt black 4 595mm, 540mm, 104mm 45 watts
SV68 Swivel Polished stainless steel 8 570mm, 1260mm, 99mm 88 watts
FS55E Freestanding Polished stainless steel 8 590mm, 900mm, 355mm 119 watts
FS66EB Freestanding Matt black 8 600mm, 1080mm, 300mm 110 watts

All five are 240 volt rails with a dry electric element. For other shapes and finishes, the heated towel ladders collection compares ladders across the range.

Swivel or freestanding

Pick by the wall first. A swivel rail needs a flat wall with room for four fixing points. A freestanding rail needs floor space and a power point within reach of its 1.4 metre lead. It suits a rental or a laundry, and any bathroom where you would rather not drill the wall. A freestanding rail is a portable unit that plugs in only. It cannot be hardwired, so it is not the choice if you want the supply hidden in the wall. A swivel rail can be hardwired or plugged in.

How the swivel works

A swivel rail turns 180 degrees on the wall, and each bar also swings on its own. Spreading the bars apart gives each towel its own space, which helps it dry. The rail also suits a corner, because it needs only two mounting points on the wall.

The two 4 bar swivel rails

The SV41 and SV41B are the same size, 595mm wide and 540mm high, and 104mm deep. They suit a small bathroom or an ensuite. The SV41 is polished stainless steel at 40 watts. The SV41B is matt black at 45 watts. Both have a 1.8 metre lead on the rail, so a plug-in rail reaches a power point 1.8 metres away. The two fixing points are 430 to 490mm apart, with two screws at each mount.

The 8 bar swivel rail

The SV68 is 570mm wide and 1260mm high, the tallest rail here. It draws 88 watts. It has an on/off switch on the bottom of the upright and a 1.4 metre lead. The supply comes in from the bottom mounting position, so the rail can be hardwired through the wall or plugged in at a point near the floor. Eight bars give room for two towels.

The two freestanding rails

The FS55E is 590mm wide, 900mm high and 355mm deep, in polished stainless steel at 119 watts, with eight bars. It has a 1.4 metre lead, an IP55 rating and a 3 pin plug. The switch is on the power point. The FS66EB is matt black, 600mm wide, 1080mm high and 300mm deep, at 110 watts and eight bars. Its switch is on top of the upright, and the switch lights up when the rail is on.

Assembling a freestanding rail

The FS66EB comes with two foot brackets, two joining rings, two screws, two black caps, four screw-in stabilising feet and an Allen key. Turn the rail upside down, push the foot brackets into the bottoms of the uprights, and fix each with a screw and the Allen key. Press the black cap over each screw head. Then turn the stabilising feet in or out until the rail stands level on your floor. The FS55E is simpler: take the screw out of each upright, fit the foot bracket and fix it with the screw supplied. You need a cross head screwdriver and a power point. Stand the rail upright and plug it into an earthed socket, then switch it on. After a short time it reaches its operating temperature. Switch it off after use.

Choosing between the two 8 bar rails

The SV68 and the FS55E both have eight bars, so the choice comes down to the wall and the watts. The SV68 is a wall rail at 88 watts. The FS55E stands on the floor and draws 119 watts, which is 31 watts more for the same number of bars. If you have a free wall, the SV68 is the better fit. If you have no wall to fix to, the FS55E gives you eight bars without a single screw in the wall.

Wiring a swivel rail

A swivel rail takes its supply at the bottom. For a plug-in rail, there is no wiring to do. The lead comes out of the lower bracket and plugs into a power point. For a hardwired rail, switch the mains off first. Then an electrician unscrews the grey cap under the lower bracket and pulls the connection capsule out through the back of the bracket. The lead comes off the terminal block and out through the grey grommet at the bottom. The grommet comes out completely, the concealed wiring cap pushes into its hole, and the supply cable is wired into the terminal block. The capsule then presses back into the bracket. On a tiled wall, the lead passes through a hole of 12 to 15mm in the tile, and the electrician needs a path for the cable from the switch position to the mounting point. The other three fixings take screw holes only. Plan the cable route before the tiler starts.

Fixing a swivel rail to the wall

Mark the four screw positions with masking tape on the wall, hold the rail against the tape, check it is level and mark each hole. Drill an 8mm hole at the centre of each mark and push in the wall plugs supplied. Check that no wire is trapped behind a bracket, then screw each bracket to the wall. Some walls need other fixings than the ones in the box, so match them to the wall: screw into the studs where possible, and use suitable anchors in a hollow wall. Fit the lowest heated bar at least 600mm above the floor, with 300mm clear of any permanent fixture, on a flat, uniform wall. Do not drill any holes until the rail is on site, so you can measure from the rail itself. The rail's measurements are enough to rough in the wall and fit timber supports behind the lining, but the holes themselves wait for the rail.

Warm-up and drying

These rails run on a low wattage and heat up quickly. You feel warmth in 5 to 10 minutes, and the rail reaches its running temperature in about 30 minutes. With no towel on it, the rail sits at about 35 degrees. A towel insulates the bars, and the rail under it reaches 50 to 55 degrees. A towel takes about 3 to 4 hours to dry, depending on the room temperature, the number of towels and how wet they are. A rail dries and gently warms a towel. It does not heat a room.

What each rail uses

Divide the watts by 1,000, then multiply by the hours to get kilowatt-hours. The table shows a 5 hour day, a week of that routine and a rail left on for 24 hours.

Rail 5 hours 5 hours a day for a week 24 hours
SV41, 40 watts 0.20 kWh 1.40 kWh 0.96 kWh
SV41B, 45 watts 0.23 kWh 1.58 kWh 1.08 kWh
SV68, 88 watts 0.44 kWh 3.08 kWh 2.11 kWh
FS66EB, 110 watts 0.55 kWh 3.85 kWh 2.64 kWh
FS55E, 119 watts 0.60 kWh 4.17 kWh 2.86 kWh

Multiply the kilowatt-hours by your own electricity rate to see the cost for your household. A rail left on all day uses almost five times the energy of the same rail on a 5 hour routine, which is the reason to put it on a timer.

Timers for swivel and freestanding rails

A timer or switch fits between the supply and a hardwired rail, so it suits a swivel rail wired into the wall. Several rails wired to one timer switch on and off together, so they cannot run on separate schedules. Timers are rated from 1 to 16 amps, and the rated load has to cover the combined watts of every rail on that timer. The Thermogroup timers and thermostats collection holds the timers made for these rails, and controllers and thermostats covers other ways to control them. A plug-in rail runs on the switch it has.

Safety and care

Put the rail on a circuit protected by an RCD. Follow the electrical rules and IP rating for the zone where it goes, and have an electrician confirm the zone before you buy. The rail is hot to touch while it runs, so supervise young children and anyone who needs help near it. Do not hang anything on it that has been in contact with oil, petroleum based products or dry cleaning fluids, and never immerse it in liquid. If the supply cord is damaged, it has to be replaced by the manufacturer or a qualified person. Clean the rail with a soft cloth and a non-abrasive cleaner, because harsh scrubbing, scratching and acid based cleaners damage the surface.

Where to go next

The Thermogroup heated towel rails collection groups the whole Thermorail range, and 240V heated towel rails compares mains-powered rails of every kind. The full range is in heated towel rails.

Frequently Asked Questions

What is the difference between a towel rail and a heated towel rail?

A standard towel rail is an unheated, wall-mounted rail for hanging and airing towels. A heated towel rail incorporates an electric or hydronic heating element that warms the rail surface. Standard towel rails are more affordable and simpler to install, while heated towel rails add warmth and faster drying. Both are available in a wide range of finishes and sizes to match bathroom accessories.

What size heated towel rail do I need?

Heated towel rail sizes are measured by total width, typically 450mm to 900mm for a single rail, and up to 1200mm for wider ladder-style units. A 600mm rail suits a single bathroom with one or two towels; a 900mm ladder rail is ideal for a family bathroom. Vertical ladder-style rails offer more drying capacity within a narrower wall footprint.

Can I install a heated towel rail myself?

Surface-mounted heated towel rails that plug into a standard GPO (power point) can be installed without an electrician. However, hardwired heated towel rails (which connect directly to the mains without a visible plug) must be installed by a licensed electrician under Australian law. Always check the installation requirements of your chosen model before purchasing.

What is a heated towel rail and how does it work?

A heated towel rail is a wall-mounted rail that uses either electric elements or a hydronic (hot water) connection to warm the rail surface, drying and warming towels placed on it. Electric heated towel rails are the most common in Australian bathrooms, they are connected to a standard power point or hardwired, and can be controlled with a switch or timer. They add comfort and help keep towels fresh between uses.