Skip to content

Marquis Reef Vanities

1 Item

  • $259 Off RRP
    Australian Made
    Marquis Reef Wall Hung Vanity with Symphony Top

    Marquis Reef Wall Hung Vanity with Symphony Top

    Checking delivery...
    $2,984
    $259 (-7%) OFF RRP of $3,243
    $259 (-8%) off RRP of $3,243

Marquis Reef Vanities Buying Guide


The Marquis Reef on this page is a 2 drawer wall hung vanity with a Symphony top, in widths from 750mm to 1800mm. The basin is included, above counter or semi-inset, and the top pull handle and the tap hole option are yours to choose. It is part of the Marquis vanities range. This guide covers the fitting and care steps for a wall hung cabinet.

Reef vanity features

This vanity is a 2 drawer wall hung design in a wide selection of cabinet finishes, with a Symphony top, and Caesarstone, Dekton or Vasari tops are also offered. The basin is included, above counter or semi-inset, and the handle is a top pull of your choice. The tap hole comes in 0, 1 or 3 options. The vanity shown is 900mm in the Australian Native finish with a Symphony Marbella top, a Brushed Brass top pull and an Arco Fluted White Matte basin, with matte brass tapware and a timber framed arch mirror.

Check the spec sheet in the downloads for the cabinet depth, the drawer layout for each width and the full list of finish names before you fix the plumbing positions, and ask for a sample if the finish matters.

Why wall hung

The wall hung design makes the floor underneath easy to clean. A wall hung vanity needs studs or reinforcement behind the wall to carry the cabinet and the top, and it is easier to plan at framing stage than in a finished tiled wall. See wall hung vanities.

Choose the top, the basin and the tap hole

The Symphony top is a solid surface. Wipe it with a soft damp cloth and mild detergent, avoid abrasive pads, and do not place hot items directly on the surface, because prolonged or extreme heat can cause permanent damage.

The basin is included, so check the basin against the depth of the cabinet and keep it back from the front edge so there is room to use it. See above counter basins. Choose the tap before you order the top, because the tap hole position is set when the top is made. A wall-mounted tap has its rough-in set before the wall is lined and tiled. Tighten the waste by hand only, because overtightening stresses the basin, and look for debris or an unlocked plug if it will not hold water. See taps and mixers.

Two drawers

Check the drawer clearance against the plumbing before you order, because water supply fittings inside the cabinet can stop a drawer closing. On a double bowl, the drawers work around two wastes.

Choose the width and bowl layout

For a room guide, 750mm suits a small main or guest bathroom with a single basin. A 900mm vanity suits a main or family bathroom with one basin, and it is not wide enough for two. A 1200mm vanity suits a large single basin or a tight double, so confirm the bowl layout on the product page. A double basin needs about 1500mm in practice, and 1800mm suits a double basin in a master ensuite. Test the footprint before you order. Mark the width and depth on the floor with masking tape, and if you have to turn sideways to pass, the vanity is too wide, too deep or both. Measure depth from the finished wall to the front of the top or basin, not only to the cabinet face.

Choose the width from the size collections: 750mm, 900mm, 1200mm, 1500mm and 1800mm. For two basins see double vanities.

Fit and height

Allow about 700mm to 750mm clear in front of the vanity to stand and move, and keep at least 450mm from the centre of the toilet pan to the side of the vanity, a common trade rule of thumb. A wall hung vanity is set on site, about 800mm to 900mm to the top, by the installer from the users, the basin and the wall. A cardboard mockup at the planned height will show you whether it is comfortable.

Sealing, moisture and after fitting

Run a continuous bead of non-acidic silicone on every edge where the cabinet or top meets the wall or floor, and extend tiles behind the furniture. Bathroom furniture should sit at least 300mm from wet areas. The materials resist moisture but are not waterproof, and the room needs ventilation. Drawers can move during transport and installation, so adjust them once the cabinet is fixed. A drawer that will not close usually has an obstruction such as a pipe or a tap hose, or the cabinet is not level and plumb. Wipe excess silicone off as you go.

Mirror and care

A mirror looks best slightly narrower than the vanity, about 50mm to 100mm in from each side, hung about 100mm to 200mm above the bench or basin rim so it clears the tap handles. See mirrors.

Wipe a cabinet with a soft cloth and a weak solution of non-abrasive detergent, and dry any spill. Wipe away pooled water around the basin, and avoid strong chemical cleaners and abrasive pads. Check the silicone monthly and reseal any that has lifted.

Above counter or semi-inset basin

The basin is included, and you choose between an above counter and a semi-inset style. An above counter basin sits on the top and shows its full shape. It adds about 100mm to 150mm to the finished height of the vanity, so it suits a wall hung cabinet that you set a little lower. A semi-inset basin sits partly into the top, with the front of the bowl projecting past the edge. It adds less height and gives a tidier line along the front of the vanity. See semi recessed basins for the shapes that work in that way.

Think about reach as well as looks. A basin set too far back makes you lean over the rim, and a basin set too far forward leaves you with wet cuffs. Aim for the tap spout to sit over the middle of the bowl. The pictured basin is an Arco Fluted White Matte, which shows how a textured basin can be the feature while the cabinet stays plain.

What the tap hole options mean

The Reef is offered with 0, 1 or 3 tap holes. Each option suits a different type of tap.

  • Zero tap holes suit a wall-mounted tap or spout, where the pipework is in the wall behind the vanity.
  • One tap hole suits a single-lever basin mixer, the most common choice in a family bathroom. See basin mixers.
  • Three tap holes suit a set with a separate spout and two handles, a style that fits a traditional or classic room.

The hole position and count are fixed when the top is made, so the tap decision comes first. If you are unsure, choose the tap, read its installation drawing, and match the hole count to it. Do not drill extra holes in a stone or solid surface top on site.

Handles and finishing detail

The Reef takes a top pull handle of your choice. A top pull sits on the upper edge of the drawer front, so the face of the drawer stays clean and the handle reads as a fine line of metal. The pictured vanity uses a Brushed Brass top pull. Match the handle finish to the tap and to the other metal in the room, such as the mirror frame, the towel rail and the light fittings. Two metal finishes can work together, but three or more start to look unplanned. See cabinet handles for other finishes.

The pictured room uses matte brass tapware and a timber framed arch mirror. That combination suits a warm, natural scheme. For a cooler scheme, chrome or brushed nickel tapware with a plain white cabinet gives a crisp result, and matte black suits a high contrast room.

Which Reef width suits which room

The five widths cover most bathrooms. Use the room, not the wall length, to decide.

  • 750mm: a small main bathroom, a guest bathroom or a compact ensuite with one person using the basin at a time.
  • 900mm: a main or family bathroom where one basin and some bench space are enough. A 900mm vanity is a sensible upgrade when 750mm leaves no room to put things down.
  • 1200mm: a larger single basin with a generous bench, or a tight double where the bowl layout is confirmed first.
  • 1500mm: a comfortable double basin vanity for a shared bathroom.
  • 1800mm: a double basin in a master ensuite, with a clear bench between the bowls.

If the room is on the smaller side, see small vanities for compact options, and if the bathroom is an ensuite, see ensuite vanities.

Questions buyers ask about the Marquis Reef

Is the Marquis Reef wall hung? Yes. The Reef on this page is a 2 drawer wall hung vanity, so it is fixed to the wall and leaves the floor clear underneath.

Does the Reef include a basin? Yes. The basin is included, in an above counter or semi-inset style.

Can I choose the handle? Yes. The Reef takes a top pull handle of your choice.

How many tap holes can I have? The Reef is offered with 0, 1 or 3 tap holes.

Is a Reef wide enough for two basins? A double basin needs about 1500mm in practice, so look at the 1500mm and 1800mm widths for two bowls.

What if the room is tiled already? A wall hung vanity can still be fitted, but the wall needs solid backing at the right height, so plan for the tiler or builder to open the wall at that spot.

What to confirm before you order

  • The width, checked with masking tape on the floor.
  • The basin style, above counter or semi-inset, and the finished height it gives.
  • The tap hole count, chosen to match the tap you plan to use.
  • The cabinet finish, checked against a sample in the bathroom light.
  • The top, Symphony or one of the other offered surfaces.
  • The handle finish, matched to the tap and mirror.
  • The wall behind the vanity, with solid backing at the right height.
  • The plumbing positions, against the drawer layout on the spec sheet.

If one of these is unclear, ask before you order. The tap hole count and the top are set when the vanity is made, so they are the two decisions to settle first.

More sizes and styles

For a white cabinet, see white bathroom vanities. Every size and style is in the bathroom vanity guide.

Frequently Asked Questions

What is a wall hung bathroom vanity and what are the benefits?

A wall hung bathroom vanity (also called a floating vanity or wall-mounted vanity) is a cabinet that is fixed directly to the wall rather than sitting on the floor. The key benefits for homeowners include a more spacious, modern aesthetic, because you can see the floor underneath, even small bathrooms feel larger and airier. Wall hung vanities are also much easier to clean, as you can sweep or mop straight underneath. They work particularly well in ensuites, powder rooms, and compact bathrooms where every centimetre counts.

Do wall hung vanities require special wall preparation before installation?

Yes. Unlike floor-standing vanities, wall hung vanities must be anchored to solid structural support, ideally wall studs or a solid timber blocking frame installed within the wall cavity. Because the vanity carries the weight of the cabinet, basin, benchtop, and everything stored inside it, standard plasterboard alone is not sufficient. If you are renovating, it is essential to discuss blocking requirements with your builder or plumber before the walls are lined. A licensed plumber or carpenter should always perform the installation to ensure it meets Australian building standards.

What height should a wall hung vanity be installed at?

The standard installation height for a wall hung vanity in Australia is approximately 850mm from the finished floor level to the top of the benchtop. However, this can be adjusted to suit the needs of your household, for example, lowering slightly for shorter users or households with young children, or raising to 900mm for taller adults. One major advantage of wall hung vanities is this flexibility: because height is set at installation, you can customise it to suit your family before the unit is fixed in place.

What size wall hung vanity do I need for my bathroom?

The most popular wall hung vanity sizes in Australian bathrooms are 750mm and 900mm wide, the 750mm suits a single ensuite or powder room, while the 900mm provides a generous benchtop and drawer space for one person in a main bathroom. For shared bathrooms or larger ensuites, consider stepping up to a 1200mm or 1500mm double vanity configuration. Always measure your available wall space and subtract approximately 100mm either side for clearance. Also check the depth, most standard vanities are 460–550mm deep, but slim 400mm options are available for tighter spaces.

What size mirror should I hang above a vanity?

As a general rule, your bathroom mirror should be the same width as or up to 50–100mm narrower than your vanity. For a 600mm vanity, a 550–600mm mirror works well; for a 1200mm double vanity, a 1100–1200mm mirror or two individual mirrors side by side suit the space. Height is flexible, most bathroom mirrors sit between 700mm and 900mm tall, depending on ceiling height and user preference.