Nidus Mardeco sliding door hardware buying guide
Nidus Mardeco is a range of flush pulls, end pulls and lock sets for sliding doors, made in zinc alloy in a choice of brass, chrome, nickel, bronze and black finishes. It is built for cavity sliders and surface sliding doors, where a projecting handle would catch the frame or stop the door entering the wall. This guide explains the parts of the range, what each set contains, which sizes decide fit, how the Euro lock sets and snib sets differ, how to choose a cylinder, and how to set out and fit a sliding door with Mardeco. The range sits within Nidus door hardware, and the wider choice of sliding door pulls is on cavity slider hardware and sliding door handles.
What a sliding door needs
A hinged door is opened with a handle that stands proud of the face. A sliding door is different. A cavity slider runs into a pocket in the wall, so the pull has to sit within the thickness of the door, and when the door is fully open the pull has to be reachable so the door can be drawn out again. That is the reason sliding door hardware is made of a few small parts: a flush pull on each face, an end pull on the leading edge, and a lock or privacy set where the door needs one.
Mardeco covers all of them. The flush pulls are recessed plates with a finger scoop. The end pull is a small pull set into the edge of the door, which is the part you hold when the door has slid mostly into the wall. The lock sets combine a flush pull with a lock, either a Euro lock that takes a key or a snib that locks from inside.
The two shapes: rectangular and radius
Mardeco comes in two plate shapes. The rectangular plate has square corners and a crisp, architectural line, and it suits a modern interior with straight lines. The radius plate has rounded corners and a softer look, and it suits a house where the other hardware is curved. Both are the same width, 45mm, and differ slightly in length: the rectangular flush pull is 190mm long and the radius flush pull is 203mm long.
The rectangular pull is also made in a long plate, 257mm long and 43.5mm wide, which is the plate used for the lock sets. It gives more room for the lock body and a longer line on the door. The end pulls are small: the rectangular end pull is 92mm long and 26mm wide, and the radius end pull is 96mm long and 26mm wide.
The sets and what they contain
Mardeco is sold as single pulls and as complete sets, so it helps to know which you need.
A flush pull sold each is a single plate for one face of the door. A door needs one on each face, so order two. A flush pull set including an end pull is a pair of flush pulls with the end pull, which is the complete passage set for a cavity door that does not lock. An end pull sold each is the small edge pull on its own, for replacing a lost or damaged one.
The cavity sliding door privacy set is a flush pull set with a privacy function, so the door can be locked from inside. It is 190mm long and 45mm wide, and it suits doors 34 to 50mm thick, with backsets of 50mm and 35mm. The radius flush pull privacy set does the same job in the radius shape, and it suits doors 42 to 50mm thick in chrome and 46 to 50mm in brass.
The Euro lock sets and snib sets
The rectangular long plate comes in two locking versions. The Euro lock set takes a Euro cylinder, which is sold separately, and it suits a door with a minimum thickness of 35mm. A Euro lock gives a keyed lock, so it suits a sliding door that needs to be locked from outside as well, such as a sliding door to a study, an ensuite with a key lock or a secondary entry. The snib lock set locks with an inside snib and has no cylinder, so it is a privacy lock only, for bathrooms and bedrooms, and it cannot be locked from outside with a key.
Choose by how the door is used. For a bathroom or bedroom, the snib set is simple and keeps the door private. For a door that needs a key, choose the Euro lock set and add a cylinder. If you are unsure, remember that a privacy lock is meant for a room where the occupant wants privacy, and it must always be possible to open it from outside in an emergency.
Choosing a Euro cylinder
The cylinder is sold separately, and the length must suit the door thickness. The M Series Euro cylinders made for the 8104 Euro lock come in four lengths. The 27mm cylinder suits doors 35 to 36mm thick. The 29mm cylinder suits doors 37 to 41mm thick. The 32mm cylinder suits doors 42 to 46mm thick. The 39mm cylinder suits doors 47 to 58mm thick. The 27mm and 29mm cylinders are four pin C4 cylinders in chrome, and the 32mm and 39mm cylinders are five pin C4 cylinders in brass.
Measure the thickness of the door, choose the length that covers it, and check that the cylinder sits flush with the plate and does not project. A cylinder that is too long projects and can be gripped from outside, and one that is too short will not reach the cam. If the door is at the border between two sizes, choose the longer one only if it still sits flush.
Sizes that decide fit
Door thickness is the first number. The privacy sets suit 34 to 50mm, the radius privacy set 42 to 50mm or 46 to 50mm by finish, and the Euro lock set needs a minimum thickness of 35mm. Backset is the second number: the privacy sets list backsets of 50mm and 35mm, and you should check which one your cavity unit and door preparation use. The length of the plate is the third: a 190mm, 203mm or 257mm plate needs a clear run on the door face, so check the height of the door and the position of the lock rail.
A cavity door also has to clear the pocket. The pull sits flush, but the plate and the lock body have depth, and the cavity frame has its own clearances. If the unit is already installed, measure the door thickness and the gap on both faces before you order, and confirm that the lock body will fit between the faces. A cavity unit supplier can confirm the limits for the model you have.
Finishes
Mardeco is made in satin brass, polished chrome, satin chrome, brushed satin chrome, brushed nickel, bronze and matte black. Satin brass and bronze are warm tones that suit timber and warm paint colours. Polished chrome is bright and reflective, and satin chrome and brushed nickel are quieter and hide fingerprints better. Matte black is neutral and suits most colours. All are zinc alloy bodies with the finish applied over them.
Choose the finish by the other metal in the room, and match it across every pull on the door and in the house. Keep the same finish on the flush pulls, the end pull and the lock set, and match the handles on the hinged doors beside them. See matte black, brushed nickel and brushed brass for the wider choice in those finishes.
Fitting a flush pull
A flush pull is fitted into a recess cut into the face of the door. Mark the outline from the plate, drill the corners, and cut the recess a little at a time so the plate sits level with the door face. A recess that is too deep leaves the plate sunk, and one that is too shallow leaves it proud. A hollow core door needs a solid block behind the pull to carry the fixing, so check the construction of the door before you cut. For a cavity slider, cut the recess before the door is hung where you can.
Fit the pull on each face at the same height, usually around hip height, and check that the two plates line up so the door looks the same from both sides. Fit the end pull into the leading edge last, and check that it clears the cavity jamb as the door slides in.
Fitting a lock set
A lock set needs a mortice pocket in the door edge as well as the recess in the face. Cut the pocket to the size of the lock body, fit the lock, and check that the bolt throws freely into the strike on the jamb. For a Euro lock set, fit the cylinder before you close the job, and test the key from both sides. For a snib set, test the snib from inside and check that the door locks and unlocks cleanly. A joiner is the safe choice for a door that is already hung, because the pocket must line up exactly with the lock body.
Care
Wipe the pulls with a soft damp cloth and dry them. Keep abrasive pads, polishes and acidic or bleach-based cleaners away from the finish. If the door sticks, check the track and the guide before you blame the hardware. Tighten the fixings once a year, because timber moves with the seasons, and keep the recess free of dust so the pull sits cleanly.
Questions people ask
Do I need one pull or two? Two flush pulls, one on each face, plus an end pull for a cavity door. Pulls sold each are single plates, and the sets include both faces.
Does the Euro lock set include a cylinder? No. The cylinder is sold separately, and the length must suit the door thickness.
Can the snib set be locked from outside? No. It locks from inside only, so it is a privacy lock and not a security lock.
Which shape suits my door? Choose rectangular for a crisp modern look and radius for a softer look, and match the shape of any existing recess.


