Skip to content

Installing a Filtered Water Tap

Installing a Filtered Water Tap

To install a filtered water tap with boiling, chilled or sparkling water, you need space under the sink for the units, a dedicated power point, a cold mains water connection with enough pressure, and a registered plumber. Most installation problems come from skipping one of these checks before buying. This guide covers each requirement using the Peppy Taps range as a worked example: how much cabinet space to allow, which trades to book, what affects the installation cost, and how to plan the tap into a renovation or a straight swap.

Peppy Taps brushed nickel 4 in 1 kitchen tap with tall rounded gooseneck spout side lever and cylindrical controls above a dark sink

What do you need to install a boiling or filtered water tap?

You need six things in place: the right tap hole, cold mains water, enough water pressure, a dedicated power point, room under the sink and a registered plumber. For the Peppy Taps range, the requirements are:

  1. Tap hole: a standard 35 mm hole in the benchtop or sink.
  2. Water supply: cold mains water only. Tank water is not suitable and voids the warranty.
  3. Water pressure: at least 150 kPa.
  4. Power: a dedicated, earthed 10 amp power point under the sink.
  5. Drainage: a drinking water connection and wastewater drainage.
  6. Installer: a registered plumber, working to national and local regulations.

No special tools are needed, but plumbing and electrical work must be done by licensed trades.

How much cabinet space should you allow?

How much cabinet space should you allow?

Allow for the units themselves, the air space around them and room to change the filter. How much you need depends on which water functions you choose.

  • Boiling and ambient - Units under the sink: Boiler, filter. Minimum air space: Boiler: 50 mm each side, 25 mm rear.
  • Boiling and chilled - Units under the sink: Boiler, chiller, filter. Minimum air space: Chiller: 100 mm each side and rear.
  • Boiling, chilled and sparkling - Units under the sink: Boiler, soda machine, CO2 cylinder, filter. Minimum air space: Soda machine: 100 mm each side and rear, plus ventilation.

Before you choose a model, measure your sink cabinet and note anything else in it, such as a pull-out bin, drawers, a garbage disposal unit or the dishwasher connection. The CO2 cylinder for sparkling models must stand upright and be secured so it can't fall. The soda machine may need a vent grille in the cabinet.
The filter cartridge needs replacing every 12 months, so mount it where you can reach it easily.

Who installs a filtered water tap, a plumber or an electrician?

Who installs a filtered water tap, a plumber or an electrician?

A registered plumber installs the tap and connects the water. You only need an electrician if there is no suitable power point under the sink.

Book the trades in this order:

  1. Electrician first, if needed. They install a dedicated 10 amp power point inside the sink cabinet.
  2. Stonemason or benchtop installer, if needed. They drill a 35 mm tap hole if your benchtop doesn't have one in the right place.
  3. Plumber last. They fit the tap, connect the boiler, chiller or soda machine and the filter, then flush and test the system.

Ask your plumber to show you how to use the controls and how to change the filter before they leave. Keep your proof of purchase for every replacement filter, because Peppy Taps requires a filter change every 12 months to keep the 2-year residential warranty valid.

What affects the cost of installing a filtered water tap?

What affects the cost of installing a filtered water tap?

The cost depends mostly on what work is needed beyond connecting the tap. A straight swap into an existing tap hole, with a power point already under the sink, is the simplest and lowest-cost job.

A few factors and how to reduce the cost;

  • No power point under the sink - An electrician has to run a new circuit or outlet. Reduce cost by adding the power point during a renovation rough-in.
  • No suitable tap hole - Stone benchtops need specialist drilling. Reduce cost by marking the tap position before the benchtop is templated.
  • Crowded sink cabinet - Extra time, or changes to drawers and bins. Reduce cost by measuring first and choose a configuration that fits.
  • Sparkling model - More units to connect, plus ventilation. Reduce cost by checking clearance and ventilation before you buy.
  • Low water pressure - Performance issues below 150 kPa. Reduce cost by asking your plumber to test the pressure first.

Get a written quote that covers removing your old tap, fitting and connecting all the units, and flushing the system.

Should you plan the tap into a renovation or add it later?

Should you plan the tap into a renovation or add it later?

It is easiest to plan a filtered tap into a kitchen renovation. You can also add one later, as long as you check the space, power and tap hole first.

During a renovation:

  • choose your tap before the cabinet design is finalised, so the sink cabinet can fit the units
  • ask your electrician to add the dedicated power point at rough-in
  • give the tap's 35 mm hole position to your benchtop installer before templating

Replacing an existing tap:

  • check whether a power point already sits inside the sink cabinet
  • measure the cabinet against the clearances above
  • a boiling and ambient model needs the least space, so it is the easiest retrofit

Once you know what fits your kitchen, compare the Peppy Taps range below and choose the configuration that suits your space.

Explore CURRENT DEALS
Up to 70% off
Up to 70% off Our biggest sale with up to 70% off and free gifts for every order over $800 Shop the Sale
WIN a Luxury Escape WIN a Luxury Escape See More
Spend $800, get free towels Spend $800, get free towels Explore Now
Spend $2500, free mirror Spend $2500, free mirror Explore Now
Spend $5000, unlock a mirror Spend $5000, unlock a mirror Explore Now
Tile Sale! Tile Sale! Shop Now
Free Colour Matching Guide Free Colour Matching Guide Unlock Now
Shop & Earn Qantas Points Shop & Earn Qantas Points Shop Now
Explore more

Deals and Promotions

Find more