Are all Geberit flush plates interchangeable?
No. A Geberit plate has to match the Geberit cistern behind the wall. Plates take the series name of their cistern: Sigma plates fit Sigma cisterns, Omega plates fit Omega cisterns, and the Alpha, a cistern for undercounter use, has its own. Round or square is a design choice and does not affect the fit. So the first step is to find out which cistern you have.
This page lists Geberit plates for Sigma cisterns and one plate for a Kappa undercounter cistern. For the cisterns themselves and the toilets sold with them, see the Geberit cistern and toilet suite packages. The plates made to suit the Sigma 8 cistern are also collected on their own page.
How to find the cistern behind your plate
Have the existing plate and frame removed, ideally by a plumber, so nothing is damaged. Behind it, read the type designation or the PA number on a label or on the protection plate. The Geberit name is usually printed on the plate too, and the sticker on the back of a Sigma 8 carries a code of the form 109.79X. Plumbers can also use the Geberit Pro app, which identifies a model from a photo of the plate and covers cisterns made from 1964. Some older cisterns need a conversion set before a current plate will fit.
Swapping a plate
When the series matches, a replacement is quick. You lift off the old plate and drop the new one in its place, and the wall does not need to be opened. If the flush misbehaves after a swap, the usual causes are incorrect installation, mismatched systems, a third-party plate, dirty or calcified valves, or a missing conversion set. A plumber should check the valves through the service opening.
The steps for a Sigma40 show what a swap involves on a Sigma cistern. You lift the old actuator plate off its mounting with gentle upward pressure, remove the two old actuator rods, and turn the distance bolts 90 degrees to free the old mounting frame. The new frame is fixed with the distance bolts and locking wedges, the new rods are shortened and locked with a 90 degree turn, and the new plate snaps in with a click. No tools are needed and one person can do it. The release method varies by plate, so a plumber should do the removal if the plate does not lift off easily.
The Sigma 20, 30 and 60 at a glance
The Sigma 20 is an ABS plastic plate with a simple geometric look, a small button for liquids and a large button for solids. It comes in round and square shapes. Finishes include matte white, gloss white, white with gold or chrome trim, matte black, black with chrome, stainless steel with chrome, matte chrome and bright chrome. The Sigma 30 is also ABS with a fingerprint resistant matte finish, in matte white, matte black and gloss white. The Sigma 60 is stainless steel with a glass finish, in white or black, and a brushed chrome version exists too. These suit Geberit Sigma 8 cisterns and are manufactured in Switzerland.
The Sigma 20 plates, one by one
The Sigma 20 is the largest group on this page. The round versions in matte white, matte black and gloss white are ABS plastic. The round Sigma 20 in stainless steel with a chrome finish is the only round version made of stainless steel instead of ABS. The matte plate with chrome trim is ABS in a fingerprint resistant matte chrome finish. The chrome plate with matt trim is ABS in chrome, and the black and chrome version is ABS with a black plate and a chrome finish.
The matte white, matte black, gloss white, stainless steel and chrome, matte chrome, chrome with matt trim, black and chrome, and white with gold trim versions suit Geberit Sigma 8 cisterns. The white with chrome trim version is suited to Geberit cisterns only, so confirm the series with a plumber before you order.
The Sigma 30 and Sigma 60 plates
The Sigma 30 in matte black and matte white is ABS plastic with a fingerprint resistant matte finish, and the gloss white version is ABS in a white gloss finish. All three suit Geberit Sigma 8 cisterns. The Sigma 60 is the glass range. The glass plates come in white and in black, both stainless steel with a glass finish, and a Sigma 60 in brushed chrome is also stainless steel. A glass or metal plate looks flatter and more architectural than ABS, and the Sigma 60 needs a minimum wall lining of 30mm so it sits flush.
The Kappa 50
The Kappa 50 is a stainless steel plate in satin chrome with clean geometric lines. It pairs with the Geberit Kappa Under Counter 150 concealed cistern and is also the access panel for servicing that cistern. It does not suit the Sigma cistern, so do not mix them.
Plate sizes and depths
Plate sizes matter for the opening you leave in the wall. The Sigma20, Sigma21 and Sigma30 are 246mm wide and 164mm high with a button depth of 12mm. The Sigma50 has the same width and height and a depth of 14mm. The Sigma60 is smaller, at 214mm wide and 132mm high.
The Kappa plates are narrower. The Kappa20 is 213mm by 142mm with a depth of 16mm, the Kappa50 is 211mm by 142mm with a depth of 15mm, and the Kappa21 is 212mm by 142mm with a depth of 10mm. For the Sigma60 the minimum wall lining is 30mm so the button sits flush with the wall. Give the tiler these sizes before the lining is chosen.
Finish names used in the Geberit range
The Sigma60 comes in brushed chrome, white, umbra and black, each with chrome trim. The Sigma50 comes in umbra, white, black and smoked reflective, each with brushed chrome buttons. The Sigma30 includes white with gold trim, chrome with matt chrome trim, black with chrome trim, matt black, sand and slate, and the Sigma21 includes a stainless steel version with chrome trim and tamper proof fixing. Umbra, sand and slate are Geberit colour names. If the colour is going next to tiles, ask for a sample or a photo in your bathroom light.
The finish is the main design decision, because the plate is the only visible part of the system. Match it to the tapware and fittings, and check that the series suits your cistern before you look at colours. For the same decision on a Caroma cistern, see Caroma concealed toilet buttons, and for the wider choice see concealed toilet buttons.
Using a Sigma plate on a Kappa cistern
Select Sigma buttons can be used with a Kappa cistern. The Sigma50, Sigma20, Sigma21 and Sigma30 plates may be used with a Sigma adapter, and the adapter must be fitted during cistern installation. The minimum hob depths are 175mm for a top press or front press on the Kappa buttons, and 205mm for a top press when the Sigma adapter is used. This is a decision for the plumber at rough in. Tell them before the cistern is fixed if you want a Sigma plate on a Kappa cistern.
Why the plate is the only visible part
Once the wall is finished, the plate is all you see of the system, so it carries the whole design. Geberit offers the widest range of options in the Sigma series, which means you can choose the plate that suits you and your bathroom, and change it when you redecorate. The cistern, the frame and the pipework stay behind the wall and do not change.
Remote buttons and service access
The remote buttons are round or square and sit up to two metres from the cistern. There is a round remote button for in-wall use, a round remote button for in-vanity use and a square remote button for in-wall or under counter use. The square remote is 129mm wide and 74mm high, and the in-vanity round is 80mm across. They suit Sigma and Kappa cisterns and come in finishes that include chrome, white with chrome or gold trim, black with chrome trim, and brushed chrome with white, black or chrome trim. The remote range also has a white care button.
You cannot service the cistern through a remote button, so separate access is required for maintenance.
What every plate includes
Each plate comes in the same box: one flush plate and the installation instructions. A specification sheet and installation instructions are also available to download. A plate does not include the cistern, the frame behind the wall or a toilet pan, so a plate is bought on top of the cistern you already have or the one you are installing. Download the specification sheet for the exact plate before the wall lining is ordered, so the sizes and the cutout are checked against the real drawing.
The plate is the only visible element of the system, and switching plates takes a few seconds. The Kappa 50 push-access plate is also the access panel for servicing the Kappa Under Counter 150 cistern.
Where a flush control can sit in an accessible toilet
If the toilet is for someone with limited reach or grip, the position of the control is part of the design. AS 1428.1 puts the flush control zone 600 to 1100mm above the floor. For a control behind the toilet, the zone is 500mm wide from the toilet centre toward the side away from the wall, and for a side control it is 300mm either side of the toilet front.
Geberit's remote range includes a white care button, and remote buttons can sit up to two metres from the cistern, which gives more freedom over where the control goes. Ask your access consultant or certifier which control suits the room, and see accessible toilets for the wider fit-out.
Where the plate fits in the room
A concealed cistern needs a wall that can hold it and a service opening behind the plate. The page on in wall concealed toilets covers what the wall needs, and wall hung toilets covers the frame. The toilets page explains set out, inlet and projection. Clean the plate with a pH neutral cleaner and avoid abrasives that mark a finish.

