Momo Bellevue Cabinet Handles Buying Guide
The Bellevue is a solid brass range from Momo Handles. It has bar pulls and D handles, knobs, backplates and an integrated appliance pull, in plain, lined and knurled textures. It was designed in-house and is the premium knurled solid brass range. It comes in finishes that include Bronze, Dark Bronze, Brushed Satin Brass, Dark Brushed Brass, Matte Black, Brushed Nickel and Gunmetal. The page covers what the three textures are, what each piece measures, how brass and its finishes behave, and how to size, fit and clean the range. For the whole brand, start at Momo cabinet handles. The Bellevue door lever sets are on the Momo Bellevue door hardware page.
The bar pull and D handle, measured
The bar pull comes in two sizes: 200mm overall on a 160mm fixing distance, and 370mm overall on a 320mm fixing distance. The projection is 36mm. The lined pull is 13mm wide, and the knurled pull is 14mm or 20mm. The knurled pull has a third size, 496mm overall on a 416mm fixing distance, with a 50mm projection. The fixing distance is the gap between the two screw holes, measured from centre to centre.
The overall length runs 40mm longer than the fixing distance on the 200mm and 370mm sizes, and 80mm longer on the 496mm size, so the handle always runs past its holes. When you replace a handle, measure the distance between the screw holes and match it to the fixing distance, not to the length of the old handle.
The knob and the backplate
The knob is 35mm across and projects 36mm, and it comes in plain, lined and knurled versions. The backplate is 35mm across, in solid brass, with a projection of 3mm on the plain version. The knurled pull and knob include screws, while the lined versions do not, so check the screw line on the exact product you order.
Screw length depends on the panel: 22mm for panels 16mm to 18mm thick, and 38mm for panels 32mm to 34mm thick. The screw must bite into the handle and stop short of the door face.
The appliance pull
The integrated appliance pull is on a 416mm hole centre. The matte black pull is 496mm overall, 402mm inner length and 50mm projection. An appliance pull is usually larger and sturdier than a cabinet pull because it deals with frequent use, the weight of the door and the suction on built-in fridges and freezers. Standard cabinet pulls are the wrong choice for appliances, since they tend to lack the strength and thickness, and a longer pull gives better leverage on a tightly sealed door. See appliance pull handles.
An appliance does not always need a pull. Fisher and Paykel makes an assisted opening accessory that opens integrated doors without a handle, and Miele makes a dishwasher that opens when you tap twice on the front.
Solid brass in a handle
Brass is generally two thirds copper and one third zinc, with a density of 8.4 to 8.73 g/cm3. Brass is heavier than zinc alloy or aluminium at the same size, and people notice the weight first: about 6.7 g/cm3 for the common zinc alloy and 2.70 g/cm3 for aluminium. The Bellevue bar pull and D handle feel noticeably heavier than most cabinet hardware, and the solid brass construction stands out against lighter zinc alloy alternatives. See solid brass cabinet handles.
Brass also changes colour. Copper reacts with sulfur to form a brown layer, and slightly acidic water can turn it into a green-blue patina. Brass is not suitable for marine use unless tin is added, because the zinc reacts with salt water. A finish slows the change: an unlacquered finish is living and develops a patina, and a clear lacquer holds the colour as made.
How the finishes are made
The finish process differs by piece. The Bronze lined pull is plated and lacquered, the Satin Brass lined pull is electroplated, and the Dull Brushed Nickel lined pull is lacquered. The Gunmetal lined pull is PVD, the Matte Black lined pull is powder coated, and the knurled pull in Dark Bronze is plated and lacquered.
PVD is a family of vacuum coating methods that make thin films on metals and other materials, with sputtering and evaporation the two common processes. The coatings have excellent abrasion resistance and are sometimes harder and more corrosion-resistant than electroplated coatings, and varying the process can make coated steel look like brass, bronze or other metals.
Powder coating is a dry powder applied electrostatically and cured under heat, and the result is harder and tougher than conventional paint. Common powders cure at 200 degrees Celsius for 10 minutes. Thin films develop orange peel, which many makers accept because it hides defects and shows fingerprints less. Plated finishes such as antique brass and brushed nickel are applied over brass, so a deep scratch shows the brass beneath.
The finishes by name
- Bronze and Dark Bronze are brown golds. Bronze is warm and Dark Bronze is deeper. See bronze cabinet handles.
- Brushed Satin Brass is a soft, even gold, and Dark Brushed Brass is a deeper brass. See brushed brass cabinet handles.
- Brushed Nickel and Dull Brushed Nickel are soft, cool greys: a metallic silver with a slight warm grey undertone and a low satin sheen that disguises fingerprints. See brushed nickel cabinet handles.
- Matte Black is non-reflective and the boldest of the group. See black cabinet handles.
- Gunmetal is a dark grey, darker, cooler and moodier than brushed nickel. See gunmetal grey cabinet handles.
Both Brushed Nickel and Dull Brushed Nickel are used, and both Bronze and Dark Bronze, so read the finish name on the exact product page. The rule for mixing is to keep a room to two metals and repeat each at least twice so it reads as a decision. Gold, brass and bronze tones pair with navy, charcoal, blue or green cabinetry and matt black works against light cabinetry as a contrast.
Choosing a bar pull size
A common rule says a pull should be about a third as long as the drawer front is wide. For a drawer 600mm across that gives about 200mm, which sits closest to the 200mm Bellevue pull. Drawers 450mm to 600mm wide take 128mm to 160mm centres, so the 160mm centre sits at the top of that band, and wider ones take 256mm to 320mm, so the 320mm centre suits a drawer of 600mm to 900mm. A tall pantry door of 600mm and above takes two 256mm pulls or a long vertical pull, and the 496mm size on a 416mm centre suits a long drawer front or a tall door.
A pull or knob sits 40mm to 60mm in from the edge that opens, near the bottom corner of an upper door and the top corner of a lower door. Pulls run horizontally on drawers and vertically on doors. To test a size before you buy, tape a strip cut to the handle's length onto the cabinet and live with it for a day.
Knob or pull
Knobs take the fingers and a single screw and suit small doors and drawers, while pulls take the whole hand. A pull is gripped with three or four fingers, which makes it the better choice for heavy drawers and for children and older people. Most cabinet knobs run roughly 25mm to 38mm across, so the 35mm Bellevue knob is near the top of the common range and suits a door or a small drawer. See cabinet knobs and cabinet pull handles.
Kitchen cabinets and door hardware
Much of the search interest in Bellevue is for door hardware, which is a different product. The range includes door lever sets, in passage, privacy and entrance configurations. Those sets are on the Momo Bellevue door hardware page. The cabinet pieces on this page are the bar pull, D handle, knob, backplate and appliance pull. If you want the same finish and texture through a house, match the cabinet pieces to the door sets by finish name, since the same names run across both.
Replacing handles
When you swap handles, match the fixing distance. A new pull with the same distance drops into the old holes without drilling. Measure from the centre of one screw hole to the centre of the other. A 128mm handle will not fit 160mm holes without new holes. If the old holes are on another centre, you will need to fill them or drill new ones, and a filled hole shows unless the door is repainted. A knob needs only one hole, so swapping a pull for a knob leaves one old hole unused and the other to fill.
In a bathroom
Bathroom fittings need wiping and drying more often than those elsewhere, because steam and moisture leave marks. Bathrooms are more humid than kitchens, and solid brass, stainless steel and quality PVD are sound choices, which includes the Bellevue brass and its Gunmetal PVD. The cabinets these handles fit are at bathroom vanities and furniture.
Caring for brass handles
An unlacquered finish can be polished, but a lacquered one should not be, because brass polish strips the clear coat and leaves patches. Several Bellevue finishes are lacquered, so avoid brass polish. Use a soft cloth with mild soapy water, wiped dry. Put the cleaner on the cloth and not on the hardware, and dry the handle straight away so water marks do not form. For lacquered finishes, use a soft microfibre cloth with mild soap and warm water if needed, dried promptly, and keep abrasive pads, powdered cleansers, ammonia, bleach and alcohol-based disinfectants away. A coating wears first where the hand lands, so wipe the grip area more often than the rest.
Related pages
For the full brand, see Momo cabinet handles. For other types and materials, see cabinet handles, solid brass cabinet handles and cabinet knobs.


