Oliveri tapware buying guide
This page holds Oliveri replacement filter cartridges: an inline water filtration cartridge for standard water use, and a replacement cartridge for the 3 way satellite filter system. They are cartridges, not taps. You buy one to keep a filter system you already own working, so the right choice depends on the system under your sink, not on a finish or a style. The guide below explains how to match a cartridge to your system, what comes in the box, how to fit and flush it, how to tell the cartridge needs changing, and where to look if you need a tap, a sink or a mixer.
What a replacement cartridge does
A filtered water system has a housing and a cartridge. The housing is the permanent part, fixed under the sink or in the line to the tap. The cartridge is the working part inside it, and it is the piece that is meant to be replaced. Over months of use it fills and slows the flow, which is normal. Changing it returns the system to how it ran when it was new, without touching the tap, the pipes or the sink.
That is why the cartridge is sold on its own. A householder with a working system needs the cartridge only. Replacing the whole system for a spent cartridge costs more time and more work than the job needs, and a cartridge swap takes a short time with the water turned off.
The inline cartridge
An inline system sits in the water line, usually in the cupboard under the sink. Water from the supply pipe passes through the cartridge on its way to the tap, so every drop that reaches the filtered tap has been through it. The inline cartridge on this page is made for standard water use. If your water supply is unusual, such as tank water or bore water, read the instructions for the system before you choose a cartridge, because the instructions state what the cartridge is made for.
The cartridge has to match the housing. Look at the housing under the sink for a model name or a code, and match it to the cartridge name. If the housing has no markings, take a photo of it before you order, and send the photo to us or to your plumber, so the match is confirmed before the cartridge is bought.
The 3 way satellite cartridge
A satellite filter system gives filtered water from its own small tap, beside the main sink tap. The cartridge on this page is the replacement for the 3 way satellite filter system.
The satellite system is a different product from the inline cartridge, and the two do not swap. Check which one you own before you order. The easiest check is the number of outlets on the sink. A separate small tap beside the main tap points to a satellite system. A single filtered line with no separate tap points to an inline system. If you are unsure, the plumber who fitted it will know, and the original paperwork will name it.
What comes in the box
Each cartridge comes with an installation kit and installation instructions. The kit holds the small parts needed to fit the cartridge to the system, and the instructions are the reference for your model. Keep both. Read the instructions before you turn off the water, because they set the order of the steps and name anything that differs between models. If the instructions and general advice disagree, follow the instructions.
Keep the box too. It carries the cartridge name, which makes the next order simple, and it is where you can write the date of the change.
Before you start
A cartridge change is a short job, and it goes better when the space is ready. Clear the cupboard under the sink so there is room to work and a place to put the old housing parts. Put a towel and a small bowl or tray under the housing, because a little water will come out when the cartridge is released. Find the isolation tap for the filtered line, or the main supply for the sink, and check that you can turn it off.
Wash your hands before you handle the new cartridge, and keep it in its wrapping until the moment you fit it. A cartridge is a clean part, and the wrapping keeps it that way. Do not touch the ends or the seals more than you need to.
Fitting the cartridge, step by step
The instructions in the box come first, and this is the usual order of work.
- Turn off the water supply to the filtered line and open the filtered tap to release the pressure.
- Release the housing and take out the old cartridge, keeping the housing upright so the water in it does not spill.
- Check the seal, the rubber ring that keeps the housing watertight, and clean it with clean water. A seal that is cracked, flat or out of place causes a leak.
- Unwrap the new cartridge, seat it in the housing the way the old one sat, and close the housing firmly by hand.
- Turn the water on slowly, check the housing for drips, and run the filtered tap to clear the air.
Check the housing again after an hour, and again the next morning, with a dry paper towel held against the joint. A slow drip shows up on the towel before it shows on the floor. Plumbing work on the supply line itself has to be done by a licensed plumber. Changing a cartridge in an existing housing is the maintenance the system is built for, but if a fitting is damaged, or the housing has to be moved, call a plumber.
Flushing a new cartridge
Run the filtered tap after fitting, before you drink from it. A new cartridge holds air, and it may release loose particles from the filter material at first. The water can look cloudy, or sputter, until the air clears. This is normal, and it stops once the cartridge has been rinsed through. The instructions for your system give the flush time, so follow that figure, and do not rely on a general number.
Taste the water after the flush. It should taste clean and have no smell. If it does not clear, check that the cartridge is seated correctly and that the housing is shut, and read the instructions again.
When to change the cartridge
The instructions state the interval for your system, and the interval depends on the filter and on how much water the household uses. A large household that drinks and cooks with filtered water uses a cartridge faster than a single person. Use the instructions as the rule, and use the signs below as a check.
- The flow from the filtered tap has slowed, and the main tap runs at its usual speed.
- The water has started to taste or smell different.
- The date you wrote on the box has passed.
Write the date of each change on the box, or on a label inside the cupboard door. It takes a few seconds and removes the guesswork. Buy the next cartridge before the old one is due, so the tap is not out of use while you wait for delivery.
After a holiday or a long gap
Water that stands in a filter for a long time can taste stale. After a holiday, or after the house has been empty, run the filtered tap for a while before you drink from it, until the water tastes fresh. If the system has stood unused for a long stretch, check the date of the last change, because a cartridge ages whether or not the water is used.
Handling and disposal
Keep a spare cartridge in its wrapping, in a clean, dry cupboard, away from cleaning products and away from heat. Do not open the wrapping until you need it. An old cartridge is spent and wet, so wrap it before it goes into the bin, and place it in a bag so it does not drip in the kitchen. Check the instructions for any disposal advice that applies to your system.
Why the tap itself matters less than the cartridge
People often look at the tap when a filtered system stops working well, and the tap is rarely the cause. A slow flow, a change in taste or a faint smell is most often the cartridge reaching the end of its use. Change the cartridge first. If the flow is still weak after a fresh cartridge, check that the supply tap is fully open, that the hose is not kinked behind the housing, and that the housing is closed properly. A fault that remains after these checks goes to a plumber.
Looking after the system between changes
Wipe the filtered tap with a soft, damp cloth and mild soap, and dry it with a soft cloth to prevent water marks. Do not use abrasive pads, bleach or strong cleaners, because they can damage a finish. Look inside the cupboard now and then, and check the housing and the hose connections for damp or a slow drip. Keep the cupboard free of clutter that could knock the housing or pull on the hoses.
If you need a tap, a sink or a mixer
The cartridges here keep an existing system running. If you are looking for a filtered tap itself, see filtered water taps and water filter taps, where the taps and their finishes are explained. For a kitchen mixer to sit beside a filtered tap, see sink mixers, pull out sink mixers, gooseneck sink mixers and standard sink mixers.
For other Oliveri products, see Oliveri, Oliveri kitchen sinks, Oliveri laundry and Oliveri kitchen accessories. Tell the plumber or the installer which sink and which filtered system you are matching, so the pieces suit each other.
Questions to settle before you order
- Is the system under your sink an inline system or a 3 way satellite system?
- Does the cartridge name match the name or code on the housing?
- Is your water supply standard water, and have you read the instructions for the system?
- Have you written down the date of the last change, and is the next change due?
- Is there an isolation tap you can turn off, and is the cupboard clear to work in?
- Do you have a spare cartridge ready for the next change?
Related pages
For the taps from every brand, start at taps. For kitchen and laundry pieces that suit a filtered system, see kitchen and laundry sets.