Zanda square cavity sliding door handles buying guide
The Zanda square cavity sliding door handle kits are 65mm square plates for doors that slide into a wall cavity, made as a passage kit and a privacy kit in stainless steel, in graphite nickel, matte black, satin brass, brushed nickel and a plain stainless finish. They suit thinner sliding doors, 32 to 38mm thick, and the privacy kit uses a claw latch. A crisp square plate gives a modern, architectural look, and it suits a house with straight lines, rectangular joinery and square-edged handles. This guide explains how a cavity handle works, what the two kits do, the sizes that decide fit, how the square plate compares with the round one, and how to plan, fit and care for a kit. The wider choice is on cavity slider hardware, and the round version is on Zanda round cavity door handle.
How a cavity slider handle works
A cavity slider runs into a pocket inside the wall, so the door disappears when it is open. A handle that stood proud of the face would stop the door entering the pocket, so cavity hardware sits within the thickness of the door. A square plate is recessed into each face, with a finger scoop to pull the door, and a small edge pull set into the leading edge lets you draw the door out of the cavity once it has slid in. Where the door needs a lock, a mechanism sits in a mortice pocket in the door edge, and a turn works it from the face.
The Zanda kit is made as a complete set, so the plates, the lock body and the edge pull suit each other and the door.
The passage and privacy kits
The passage kit has no lock. It suits a sliding door between living areas, a pantry or any door that is never locked, and it gives you the flush plates and the edge pull. The privacy kit adds a lock that works from inside with a turn, and it uses a claw latch, a hook that catches the strike as the door closes. It suits a bathroom, an ensuite or a master bedroom, where the occupant wants privacy.
A privacy lock is made for a room where the occupant wants privacy, not security, and it must be possible to open it from outside in an emergency. Check the release on the outside plate, test it the day the lock is fitted, keep a tool where the household can find it, and show everyone in the house how it works, including older children.
Why a square plate
A square plate is crisp and architectural. Its straight edges and sharp corners echo rectangular joinery, square-edged handles and square basins, so it suits a modern house with a strong geometry. It also shows its alignment: because the edges are straight, the plate must sit square to the door, so the fitting is exact, and a well-fitted square plate reads as a considered detail. If the other hardware in the room is round, such as round roses or round knobs, the round plate agrees better. If the room is full of straight lines, the square plate agrees with it.
Sizes that decide fit
The plate is 65mm by 65mm, and the kits suit doors 32 to 38mm thick, which is thinner than the range for the round kits. Measure the thickness of the door with a tape, and check that it falls within the range. A door that is thinner than 32mm or thicker than 38mm does not suit the set, so check before you order. The thinner range makes the square kit a good choice for a lighter sliding door, such as an interior door of standard thickness.
The recess for a square plate is square, so it is cut with a router or a chisel and not a hole saw. The three numbers to check before you order are the door thickness, the size of the recess and the clearance in the cavity unit. The plates sit flush, but the lock has depth and the frame has its own clearances, so measure the gap on both faces and confirm that the lock body will fit. A cavity unit supplier can confirm the limits for the model you have.
The edge pull
Each kit includes an edge pull, which lets a user draw the door out of the cavity with ease. When the door has slid mostly into the wall, the edge pull is the only part you can reach, so a cavity slider without one is hard to open from the open position. Fit it into a recess in the leading edge, so it sits flush and clears the jamb as the door slides in. If you replace the plates on a door that already has an edge pull, check that the old one is in good order and the finish matches.
Finishes
The kits are made in graphite nickel, matte black, satin brass, brushed nickel and stainless steel. Graphite nickel is a dark grey between nickel and black. Matte black is neutral and suits black frames and tapware. Satin brass is a warm gold with a brushed look that suits timber and Hamptons style homes. Brushed nickel and stainless steel are quiet silvers that hide fingerprints and suit stainless steel and chrome tapware. The bodies are stainless steel with the finish applied over them.
Choose the finish to match the handles on the hinged doors beside the sliding door, since the two are seen together, and keep the same finish on the plates and the edge pull. See matte black, brushed brass and brushed nickel for the wider choice in those finishes.
Reading the product names
The names follow a pattern. In Zanda Square Cavity Sliding Privacy Door Handle Kit Graphite Nickel, the brand is Zanda, the shape is square, the door is a cavity sliding door, the function is privacy, the product is a handle kit and the finish is graphite nickel. A name with Passage means no lock. Each kit is one set for one door, with the plates for both faces and the edge pull.
Choosing a function
The function decides which kit you need. A passage kit suits a door that is never locked, such as a door between a hallway and a living room. A privacy kit suits a bathroom, an ensuite or a master bedroom. Choose the simplest function that does the job, since a lock adds parts and fitting time. If the door is a bathroom door that may be used by children or by someone who may need help, make sure the release works and everyone knows where the tool is.
Preparing the door
The door should be prepared before the hardware arrives. Cut or confirm the square recess for each plate, the mortice pocket for the lock body in the edge, and the recess for the edge pull, and check that the door is square and the right thickness. Give the door maker the specification before the leaf is made, and ask for the preparation to be done in the workshop, where it is easier to get right. If you are retrofitting hardware to an existing door, check the existing recesses against the new plate before you buy.
Fitting a kit
Mark the position of the plate on each face at the same height, usually around hip height, and check that the two plates line up so the door looks the same from both sides. Mark the outline of the square recess, drill the corners, and cut the recess a little at a time so the plate sits level with the door face. A recess that is too deep leaves the plate sunk, and one that is too shallow leaves it proud. Cut the mortice pocket in the door edge for the lock body, fit the lock, and check that the latch works freely before you fit the plates. A hollow core door needs a solid block behind the plate to carry the fixing, so check the construction of the door before you cut.
Setting the height and position
The plate should sit at a height where a hand falls naturally on it, usually around hip height, the same as the handles on the hinged doors in the house. On a cavity slider the position along the door matters as well. The plate sits near the leading edge, close enough that you can reach it when the door is nearly closed, but far enough from the edge that the recess does not weaken the stile. Mark both faces at the same height with a level so the plates line up through the door, and keep the edges of the square plate parallel to the door edge.
Care
Wipe the plates with a soft damp cloth and dry them. Keep abrasive pads, polishes and acidic or bleach-based cleaners away from the finish. If the door sticks, check the track and the guide before you blame the hardware. Tighten the fixings once a year, and keep the recess free of dust so the plate sits cleanly. Matte black needs a gentle wipe to keep the coating even, and a brushed finish hides fingerprints better than a polished one.
Common mistakes
A few errors come up often with cavity kits. The first is choosing a kit for the wrong door thickness, which leaves the plate loose or the lock too deep. The second is cutting the recess before checking the cavity unit clearances. The third is fitting the privacy side on the outside of the room, which locks the door from the wrong face. The fourth is ordering the wrong function, such as a passage kit for a bathroom. The fifth is forgetting the edge pull, so the door cannot be drawn out. Check each before you order.
Questions people ask
Do I need one plate or two? Two plates, one on each face, plus an edge pull for a cavity door. Each kit includes the plates and the edge pull.
What door thickness does the square kit suit? Doors 32 to 38mm thick.
How is the square kit different from the round? The shape of the plate and the recess. The square suits a house with straight lines, and the round suits one with curves.