Nero taps buying guide
This page holds the Nero taps we sell: basin mixers, bath fillers, shower mixers, kitchen and sink mixers, laundry taps and spouts, in the same range names and finishes for every room of the house. Nero is designed in Australia and made in the brand's own factory in China. Nero sits in the mid-range of Australian tapware, and the reason buyers choose it is consistency: one finish and one design language from the basin to the shower to the towel rail. This guide covers how Nero taps are made, what each range looks like, how to read the finish names, and what to measure before you order. For the whole brand, including showers and accessories, see Nero tapware.
What Nero taps are made from
Nero taps are mainly made from lead-free DZR brass and stainless steel. DZR means dezincification resistant: the brass is made to resist corrosion from the inside. The mixer body is solid brass with a ceramic disc cartridge. A ceramic disc cartridge uses two ceramic plates to control the water and is less prone to dripping over time than older washer designs. A good ceramic disc cartridge gives smoother operation and better shut-off over time, and you should check that a local plumber can source replacement cartridges, aerators and handle parts before you buy. For Nero that check is short. Cartridges, handles, hoses and spouts are all available as spare parts. Spare parts are supplied for most products, and availability depends on the model and its age.
Zen and Pure are the exception to the brass rule. They are made in 316L stainless steel, a grade chosen where corrosion resistance matters most. They are the range for outdoor use, and Zen is the one to start with for a coastal balcony, an outdoor kitchen or a pool bathroom. See the Zen SS316L collection.
Lead-free and drinking water
The National Construction Code sets a limit of 0.25 percent lead for plumbing products that carry drinking water, and the limit applies from 1 May 2026. Nero's drinking water products have been made with low-lead materials since April 2023. Only products that contact drinking water need to meet the rule, which is why the kitchen tap and the basin tap are the two to check. Zen and Pure suit lead-free needs across the whole selection. If lead-free is a requirement on your project, see lead-free taps.
Choosing a range by style
Nero names its ranges, and the range sets the shape of the handle, the spout and the body. They break down like this:
- Mecca has a cylindrical body and a slim pin lever. It has the widest choice of finishes in the brand and suits minimal, contemporary rooms. Shop the Mecca range.
- Bianca has a flatter, architectural profile with softened edges, which pairs with square basins and wall mounted fittings. It is the broadest range, covering mixers, shower sets, spouts, accessories and sensor taps. Shop the Bianca collection.
- York is the heritage option, with cross handles and sweeping spouts on a brass body with a ceramic disc cartridge. It suits heritage and farmhouse rooms. Shop the York range.
- Opal has knurled, faceted handles that catch the light, and a progressive single handle version. It works as a feature tap in an ensuite or powder room. Shop the Opal collection.
- Serenity has curved, organic forms and marble handle options, so each handle has its own veining. Shop the Serenity range.
- Pure and Zen are minimal, leverless designs in 316L stainless steel, with a progressive handle that turns instead of lifting. Zen offers laminar flow, a smooth and clear stream, as a feature. Shop the Pure collection.
- Dolce and Ecco are simpler lines: Dolce is soft and rounded, and Ecco is minimal and lead-free. See Dolce and Ecco.
Reading the finish names
The finish name tells you how the surface is made. Chrome and matte black are electroplated finishes. Brushed nickel, brushed gold, brushed bronze, gun metal grey, graphite, aged brass and PVD black are PVD finishes, and matte white is a powder coat. PVD stands for physical vapour deposition, and Nero has moved away from traditional plating toward PVD over recent years. A PVD coating lasts over 10 years when it is applied and looked after correctly, and it is free of volatile organic compounds in the coating process. Check the product page for the finish you want.
Plumbing suppliers pair the finishes with what they sit beside:
- Chrome suits white tiles and classic bathrooms. See chrome taps.
- Matte black gives contrast against white basins, pale tiles and timber vanities. See black taps.
- Brushed nickel is a soft silver that works with natural stone, terrazzo and neutral palettes. See brushed nickel tapware.
- Brushed gold suits timber cabinetry, warm whites and marble. See gold taps.
- Brushed bronze suits earthy tones, organic materials and dark tiles. See bronze taps.
- Gunmetal and graphite suit dark cabinetry and concrete-look tiles. See gunmetal tapware.
- White tapware suits a Scandinavian or minimal scheme. See white tapware.
Looking after the finish
The most effective way to extend the life of a finish is to stop water drying on it, especially in hard water areas. Wipe the tap after use. Clean with a mild detergent and a soft cloth, avoid harsh chemicals and abrasive pads, wipe matte and PVD finishes gently, and polish chrome now and then. Abrasive cleaners and scouring pads scratch the coating. In coastal and humid areas, brushed stainless steel, PVD coated matte black or brass, and well plated chrome are the finishes that resist salt air.
Choosing the mounting before the tap
Decide the installation method first, then how easily the tap can be serviced, then the look. The choice matters most for wall mounted sets: the plumbing must be roughed in before tiling, so the decision is locked in once the tiles go on. In a full renovation, settle it with your plumber early. Basin mounted taps are more forgiving, and suit most standard Australian vanity setups. For baths, the choice splits by bath type: floor or wall mounted spouts for a freestanding bath, and hob mounted spouts on the deck of a built-in bath. Wall mounted taps need a wall water inlet and exact plumbing measurements before you buy.
Taps for the bathroom basin
Basin mixers are the main configuration: one lever sets both temperature and flow. Run this short checklist before you order:
- Tap hole size. Most standard Australian basin mixers need a single hole of 35mm.
- The distance between the hot and cold supply lines.
- Basin depth and rim height. Above counter and vessel basins usually need a tall mixer or a wall mounted tap for clearance, and inset and undermount basins suit standard mixers or three piece sets. Measure the rim height and confirm the spout clears it.
- Spout reach. Confirm it covers the basin so water does not splash against the side.
- Water pressure. Long reach and high spout taps need more pressure to perform, and compact basin taps suit lower pressure systems better.
Nero makes short, tall and wall mounted basin mixers, and the style you pick has to match how the basin is built. Three piece sets split the controls into two handles and a central spout, a classic look that needs more bench space. Browse basin mixers across brands, or filter this page by mounting.
A wall mounted set needs the pipe centres to match. The typical spacing is 150mm, so measure the rough-in before you choose between sets. Some wall sets are sold as the trim only, some as a spout only, and some as a complete set, so check what comes in the box. An in-wall mixer needs a matching in-wall body for its range. Mecca and Bianca pair with Nero's Premium bodies, Dolce, Celia and Ecco with its Project bodies, and Zen and Pure with stainless steel 316L bodies, and the Opal and York in-wall bodies are not sold separately. Check the product page before you add it to the cart. See wall basin and bath mixer sets.
Taps for the bath and shower
For a shower mixer, choose a round or square plate and check its size: 60mm, 80mm or a separate back plate. For the bath, measure the distance from the wall to the spout, because that sets the spout length you need. The range includes fixed bath spouts, swivel spouts and freestanding bath fillers, and wall mixers that control temperature and flow for a shower or bath from one fitting. A twin shower hand piece can be swapped if you ask for it on the order, so ask before you buy if you want a different hand piece. See shower mixers and bath fillers.
Taps for the kitchen and laundry
The same ranges run into the kitchen. A standard sink mixer is the straightforward choice. A gooseneck sink mixer has a tall arched spout, and a pull out sink mixer has a hose that draws out of the spout. A pot filler mounts on the wall behind the cooktop, and sensor taps switch on without a touch. See all sink mixers and kitchen taps. Wall, hob or floor mounting changes the labour and the future servicing, so settle the mounting before you pick the style.
In the laundry, use laundry taps for the trough and washing machine sets for the supply to the machine. The manufacturer's FAQ notes that only products that contact drinking water need to be lead-free, so a laundry trough tap and a kitchen tap are different cases.
Water efficiency and flow
WELS is the Australian water efficiency label, and a higher star rating means the tap uses less water. Use the rating as a screening tool: it compares water use, but it does not tell you whether the tap suits your basin, your pressure or your daily use, so balance efficiency against usable flow. Aerator design changes how the stream feels. Check the WELS label on the specific product, because the rating belongs to each product and not to a range.
Bring the room together
Once the taps are chosen, the next decisions are the basin, the shower and the accessories. The full taps collection shows other brands for comparison, and the Nero wastes and traps match the finish of the tap above them.


