Bathroom basin taps buying guide
A bathroom basin tap, a bathroom sink tap and a vanity tap are the same fitting, and this page holds all of them: single lever mixers, three piece sets, wall mounted sets and the tall mixers made for bowl basins. You use this tap more times a day than almost any other fitting in the house, and it sits at eye level in the spot where the tiles, basin and cabinetry meet. The guide below sets out the types, the measurements that decide fit, what the body and cartridge should be made of, and how to choose and look after a finish.
Which type of basin tap suits your vanity
Choose the type from the basin and the vanity first, then the look. This table covers the options on this page.
| Type | Suits | Check before you order |
|---|---|---|
| Single lever basin mixer | Most vanities with one tap hole | Hole size, spout height and reach. See basin mixers. |
| Tall basin mixer | Bowl basins that sit on the bench | Height to the spout against the rim. See tall basin mixers. |
| Three piece set | Traditional and Hamptons rooms, basins with three holes | Three holes and bench space. See three piece taps. |
| Wall basin mixer set | Wall hung basins and floating vanities | In-wall plumbing before tiling. See wall basin and bath mixer sets. |
| Wall top assemblies and spout | Basins with a separate spout and handles | Pipe centres and spout length. See spouts. |
For a busy family bathroom, a single lever mixer is the practical call: one hand sets flow and temperature, and a mixer has fewer places for limescale to collect than a pair of handles. A three piece set earns its place where the room has a period or Hamptons character, because the matched handles and central spout suit that look. If you are choosing the basin and the tap together, our bathroom basins show the hole layout of each basin.
Are bathroom basin taps a standard size
Mostly, and that is why the exceptions matter. Most modern basin mixers fit a single 35mm tap hole, so a basin with one standard hole takes almost any of them. A three piece set needs three holes and a mixer needs one, which means a mixer is not a direct replacement for a three piece set unless the basin or bench can be drilled or blanked off to suit.
Some basins and benchtops have no tap hole at all. These take a wall mounted tap, or a bench mounted tap fitted through a hole drilled in the vanity top. Stone, concrete and timber tops need that hole position settled before the top is cut. Check the distance between the hot and cold supply lines, the basin depth and the space behind the basin for the handle swing before you order.
Replacing an existing basin tap
The hole matters more than the style. Keep the existing layout where you can: a mixer replaces a mixer in the same hole, and a three piece set replaces a three piece set at the same spacing. Measure the hole, the spacing between the handles of a three piece set, and the height under the bench for the supply hoses. A bench mounted or basin mounted tap is among the quickest bathroom updates, because a plumber can work from under the vanity without opening a wall.
Choosing a tap by room
A main bathroom is used all day, so a mixer in a finish that wipes clean and hides water spots is the safe choice. An ensuite is more personal, and the feel of the lever in the hand counts as much as the look. A powder room is used briefly and seen more than it is worked, which makes it the place for a tall mixer or a wall set with a strong shape.
Spout height and reach
Height is the decision that goes wrong most often, and it depends on the basin. A standard height mixer suits an undermount, inset or semi-recessed basin, where the spout sits above the bowl with room to spare. A bowl basin that stands on the bench has a raised rim, so it needs a tall mixer or a wall mounted tap, otherwise the spout sits below the rim and the water runs against the side.
Reach decides where the water lands. The stream should fall in the centre of the bowl, not on the rim and not against the plughole. Reaches on this page run from about 110mm on compact mixers to about 230mm on long spouts. A spout that is too tall or too long for a shallow basin splashes, and one that is too short misses the centre. Check the height and reach on the product page against the depth of your basin, and leave clearance for the mirror or shelf behind the tap.
Hob mounted or wall mounted
Choose the mounting first, then how easily the tap can be serviced, then the look. A hob mounted tap sits in the vanity top or the basin deck. It is the more forgiving option on a renovation, because the plumbing comes up through the cabinet and a plumber can reach it from below.
A wall mounted tap keeps the bench clear, leaves no base plate to collect limescale, and suits floating vanities. The cost is planning: the plumbing is roughed in before the tiles go on, so the choice is locked in early. Wall sets need the pipe centres to match the spout, and some come with the in-wall body while others are trim only, so check the box contents.
Cartridge, body and water pressure
We recommend a solid brass body and a ceramic disc cartridge. A ceramic disc cartridge uses two ceramic plates to control the water, resists wear and shuts off cleanly for years. The cartridges on this page are 25mm, 28mm or 35mm, depending on the range. Ask your plumber whether replacement cartridges and aerators can be sourced locally for the range you pick.
Most mixers here carry 5 or 6 WELS stars. A higher rating means the tap uses less water, but it does not tell you whether the tap suits your basin or your pressure. Mains pressure gives you the most choice. Low pressure and gravity fed systems need a tap rated for it, and a traditional look does not mean a tap works at low pressure, so check the rating with a plumber. Some mixers have a cold start setting: the lever sits in the centre position and sends cold water only, so a quick hand wash does not fire up the hot water system.
Lead-free tapware and WaterMark
The National Construction Code limits lead in plumbing products that touch drinking water to 0.25 percent from 1 May 2026, and many of the mixers here are lead-free brass. Confirm WaterMark approval on the product page, because it affects legal installation in Australia. A licensed plumber should install any basin tap.
Choosing a finish for the vanity
Finish is the last decision, and it should match the other metal in the room. Each finish below has its own guide and range.
- Chrome suits white tiles and classic bathrooms and is the easiest to match later. See chrome taps.
- Matte black gives contrast against pale tiles, white basins and timber vanities. See black taps.
- Brushed nickel is soft and muted, and suits natural stone and neutral palettes. See brushed nickel tapware.
- Brushed brass and brushed gold bring warmth against timber, marble and warm whites. See brushed brass taps and gold taps.
- Gunmetal and bronze are dark and warm, and suit dark cabinetry and concrete look tiles. See gunmetal tapware and bronze taps.
Limit a room to two finishes, and let one lead. Brushed finishes hide fingerprints and water spots better than polished chrome or flat black. Judge a finish in the light of your own bathroom, beside your tiles, because colour names are not standard across makers and the same name can look different from one range to the next. Taps, towel rails, shower fittings and cabinet handles read as a set, so a full run from one range keeps the tone even.
How to care for a basin tap
Wipe the tap with a soft microfibre cloth and warm water after use, and clean it weekly with a mild detergent. Dry it so water does not set on the surface, which matters most in hard water areas. Avoid bleach, harsh bathroom sprays, abrasive pads and scourers, because they scratch and dull any finish. A PVD coating resists scratching and tarnish better than standard plating, and it still needs gentle cleaning. Check the seals and cartridge now and then, and fix a drip early.
What comes in the box
The contents depend on the tap. A basin mixer comes with the mixer, installation instructions and usually an installation kit. Many bench mounted mixers add a pair of 450mm braided flexible hoses, one hot and one cold. A wall basin and bath set comes with the in-wall kit, and a wall mixer trim kit is sold with its in-wall body. Three piece sets come with a hot tap, a cold tap and the spout. Read the product page for the exact list before you order, and buy a waste separately if your basin does not include one.
Taps by brand
The basin taps on this page come from Phoenix taps, Caroma taps, Meir taps, Fienza taps, Clark taps, Dorf taps and Modern National tapware. Staying with one brand and range keeps the handle, spout and finish consistent across the basin, shower and bath. The full group is on our taps page.
Complete the vanity
Once the tap is chosen, the basin and the vanity are the next decisions. The tap hole layout, the basin depth and the finish all carry over, so settle them together and you avoid a mismatch at installation.


